Maximum‐power‐point tracking method of photovoltaic power system using a single transducer

This paper describes a novel strategy of maximum‐power‐point tracking for photovoltaic power generation systems. A unique feature of this method is the capacity to see the maximum power point using only a single transducer, that is, a Hall‐effect CT or an isolation amplifier. Output power of the photovoltaic can be estimated with an average value and ripple amplitude of the detected reactor current or the capacitor voltage. A conventional hill‐climbing method is employed to seek the maximum power point, using the output power estimated with only the current or voltage transducer. In this paper, not only a theoretical aspect of the proposed method is discussed, but also experimental results are presented to prove the feasibility of the method. © 2007 Wiley Periodicals, Inc. Electr Eng Jpn, 160(1): 79– 86, 2007; Published online in Wiley InterScience ( www.interscience.wiley.com ). DOI 10.1002/eej.20275     

Difference in the detection limits of flaws in the depths of multi-layered and continuous aluminum plates using low-frequency eddy current testing

We examined the difference in the detection limits of flaws in the depths of multi-layered and continuous aluminum plates using low-frequency eddy current testing. The detection limits were measured by using a magneto-resistive sensor. Comparing the frequency of an applied magnetic field, the detection limit at 50 Hz is deeper than that at 1 kHz. Comparing the sample structure, the detection limit in the multi-layered samples is deeper than that in the continuous samples. These results are likely due to the differences in the skin depth and conductivity of the sample.     

The relationship between acoustic emission signals and cutting phenomena in turning process

The development of intelligent manufacturing by using machine tools is advancing in leaps and bounds. To maintain accuracy in machining and in the interests of fail-safe operation, monitoring of the cutting state or the final machining is very important. Acoustic emissions (AE) comprise elastic stress waves produced as a result of the deformation and fracture of materials. By measuring the AE generated during a turning process, it is possible to estimate the state of the machining operation. The correlation between cutting phenomena and AE in a turning process was examined experimentally by using a steel workpiece and a cermet tool in a numerically controlled turning process. The process of formation of chips, the types of chip, and the shear angle all markedly affected the AE signals. There was a strong negative correlation between the shear angle and the AE signal level. Similar results were obtained for various feed rates and for workpieces of various degrees of hardness. Correlations related to surface roughness and to tool wear are also described that permit the evaluation of the state of the turning process.     

Design and performance of high-precision MT-type connector for1.55-μm zero-dispersion-shifted fiber-ribbon cables

We have found that, for dispersion-shifted fiber (DSF) ribbons, the accuracy with which the fiberhole is positioned in the connector ferrule must be less than 0.6 μm to realize a low average insertion loss of about 0.1 dB. By using the high-precision ferrules, we realized MT-type connectors that achieved a very low average insertion loss of 0.11 dB with a maximum of 0.37 dB. These connectors also satisfied mechanical and environmental stability requirements. We have confirmed that our high-precision MT-type connectors can be used for joining DSF ribbon     

Hydrogen production by combining two types of photosynthetic bacteria with different characteristics

The double-layer photobioreactor using two types of photosynthetic bacteria, Rhodobacter sphaeroides RV and its reduced-pigment mutant, MTP4, was developed for efficient hydrogen production. The two types of bacteria had different characteristics on light energy, hydrogen production rate and conversion efficiency. MTP4 produced hydrogen more efficiently under high light conditions and RV did so under low light conditions. Illuminated light toward the surface of a photobioreactor quasi-exponentially declines as it penetrates into the reactor. When two types of bacteria were placed using the developed reactor according to this light distribution, the hydrogen production rate reached 3.64 l/m²/h at a light intensity of 500 W/m² in 24 h and the conversion efficiency of light energy to hydrogen was 2.18%. These values were 33% higher than those of only using RV. The low light in the deep part of the reactor was utilized efficiently, resulting in a higher hydrogen production rate.     

Efficient hydrogen production using a multi-layered photobioreactor and a photosynthetic bacterium mutant with reduced pigment

A multi-layered photobioreactor (MLPR), where the light paths were formed by the localization of bacterial cells, was constructed for efficient hydrogen production. The performance was investigated under several conditions in order to clarify the effect of this reactor on hydrogen production. An analysis of the hydrogen production profile showed that the MPLR utilizes both the light that directly illuminates its surface and the light induced and diffused from its light paths for hydrogen production. It was also found that the hydrogen productivity in the MLPR was more than twice that in a plate-type reactor. When a photosynthetic bacterium mutant with reduced pigment, MTP4, was used, the maximum hydrogen production rate reached 2.0 l/m² h, which was 38% higher than that of a conventional plate-type reactor. The synergistic effect of the improvement in the reactor and the modification of the bacteria was brought about by the combination of the MLPR and MTP4, and resulted in an improvement in the hydrogen production.     

Internal stress behavior of the short ceramic fiber reinforced aluminum alloy under tensile deformation

The in situ measurement of phase stress under tensile deformation on an A6061 alloy reinforced with SiC whiskers (Al/SiCw MMC: Metal Matrix Composite) was performed using the X-ray diffraction technique. In order to raise a preciseness of measurements, we applied a profile fitting technique to separate the nearby located diffraction peak. Tensile deformation on elastic to plastic range was applied by four points bending device and discussed internal stress behavior in the short ceramic fiber reinforced MMC. Phase stress in Al matrix was increased linearly up to 2800×10⁻⁶ in strain and then saturated immediately. On the other hand phase stress in SiC whiskers shows an unstable stress behavior. It was decreased at first because of the Poisson's effect from Al matrix but reversed over 500×10⁻⁶ applied strain. The measured phase stress behavior in elastic region agreed with the calculations using micromechanics based on Eshelby/Mori–Tanaka model except for this unstable internal stress region. The macro stress behavior in plastic region was extremely small than that of the tensile test results. It supposed that the mechanism of strength is not so much the fiber reinforcing as the dispersion strengthening like the Orowan mechanism. Regarding the fatigue property, ΔK_th of the Al/SiC MMC, this was lower than that of the A6061 alloy. On the Al/SiCw MMC specimen, many micro void formations were observed around the fatigue crack tip even under the ΔK_th of A6061. It was considered that these were caused by the high gradient of residual stress on composite process and the unstable stress behavior in low ΔK region.     

Managing networks of communities of practice for organizational knowledge creation A Knowledge Management imperative in the era of globalization

This article explores some imperatives of Knowledge Management for organizational knowledge creation in the era of globalization. As the transformation of Knowledge Management practices of Japanese firms in 1990s shows, Nonaka and TakeuchVs original model of organizational knowledge creation needs to be expanded by incorporating the concept of “community of practice” as the “engine” of knowledge creation. As an attempt for such expansion, it proposes a model of knowledge-creating organization as a self-organizing network of interactive, overlapping, and self-managing communities of practice. This article also explores some organizational conditions and managerial implications to prevent “malfunction” of communities of practice in the threats of globalization and to facilitate their dynamic evolution. Knowledge-creating organizations and their managers need to give due recognition to and support for “differences” that exist not only among diverse communities of practices but also within each communities. At a micro level approach, they need to “empower” community members by encouraging “ story-telling” or “narrative” of members’ lives in the communities and by assuring “transparency” of activities and resources to the members. As a macro level approach, they need to develop a “communitarian” organizational structure that fits to organizational knowledge creation in “multiculturalization” of societies.     

Short‐current pulse‐based adaptive maximum‐power‐point tracking for a photovoltaic power generation system

This paper focuses on a maximum‐power‐point tracking method of photovoltaics via use of the short‐current pulse. It has been reported that the optimum operating current is proportional to the short current and that maximum‐power‐point tracking can be performed by detecting the short current. The proposed method utilizes the intermittent short‐current pulse to estimate the optimum operating current and its operating characteristics have experimentally been verified. Also, an adaptive mechanism to identify the parameter between the optimum current and the short current is discussed. A prototype of the controller has been set up and the experimental results have demonstrated excellent performance, proving the feasibility of the system. © 2002 Scripta Technica, Electr Eng Jpn, 139(1): 65–72, 2002; DOI 10.1002/eej.1147